Heat Treatment Process of Powder Metallurgy Materials
Nov 27, 2022
Heat Treatment Process of Powder Metallurgy Materials
Do you know the heat treatment process of powder metallurgy materials? Nowadays, powder metallurgy materials are used more and more widely. They have replaced low density, low hardness and strength cast iron materials. Obvious advantages. The heat treatment of powder metallurgy materials includes quenching, chemical heat treatment, steam treatment and special heat treatment in the following forms:
1. Quenching heat treatment process
The heat transfer rate of powder metallurgy materials due to the existence of pores is lower than that of compact materials, so the hardenability is relatively poor during quenching. In addition, during quenching, the sintering density of the powder material is proportional to the thermal conductivity of the material. Due to the difference between sintering process and compact materials, powder metallurgy materials have better internal structure uniformity than compact materials, but the micro area is small. Therefore, for non-uniformity, the complete austenitizing time is 50% longer than the corresponding forging, and when alloy elements are added, the complete austenitizing temperature is higher and the time is longer.
In the heat treatment of powder metallurgy materials, in order to improve the hardenability, some alloy elements, such as nickel, molybdenum, manganese, chromium, vanadium, etc., are usually added, which play a role in dense materials. It can significantly refine grains. When it is dissolved in austenite, it will increase the stability of undercooled austenite, ensure the austenite transformation during quenching, increase the surface hardness of quenched materials, and increase the quenching depth. In addition, powder metallurgy materials shall be tempered after quenching. The temperature control of tempering treatment has a great influence on the properties of powder metallurgy materials. Therefore, the tempering temperature should be determined according to the characteristics of different materials to reduce the influence of tempering brittleness. Typical materials can be tempered for 0.5-1.0 h in air or oil at 175-250 ° C.
powder metallurgy
2. Chemical heat treatment process
Chemical heat treatment usually includes three basic processes: decomposition, absorption and diffusion. For example, the reaction of carburizing heat treatment is as follows:
2CO ≈ [C]+CO2 (exothermic reaction)
CH4 ≈ [C]+2H2 (endothermic reaction)
Carbon is decomposed and absorbed by the metal surface, and gradually diffuses inside. Quenching and tempering the material after obtaining sufficient carbon concentration will increase the surface hardness and hardening depth of powder metallurgy materials. Due to the existence of pores in powder metallurgy materials, active carbon atoms permeate from the surface to the interior, completing the process of chemical heat treatment. However, the higher the density of the material, the weaker the porosity and the less obvious the effect of chemical heat treatment. Therefore, reducing atmosphere with high carbon potential must be used. According to the pore characteristics of powder metallurgy materials, their heating and cooling rates are lower than those of compact materials, so the heating time should be extended to increase the heating temperature.
Chemical heat treatment of powder metallurgy materials includes carburizing, nitriding, vulcanization and multi-element. In chemical heat treatment, the hardening depth is mainly related to the density of the material. Therefore, corresponding measures can be taken during the heat treatment process. For example, when carburizing, when the material density is greater than 7g/cm3, the time can be extended appropriately. Through chemical heat treatment, the wear resistance of materials can be improved. The non-uniform austenitic carburizing process of powder metallurgy materials can make the carbon content on the surface of the treated material layer reach more than 2%, and the carbide is evenly distributed on the surface of the penetration layer. It can improve the hardness and wear resistance.
3. Steam treatment
Steam treatment is to oxidize the surface of materials by heating steam, so as to form oxide film on the surface of materials, thus improving the performance of powder metallurgy materials. Especially for the surface anti-corrosion of powder metallurgy materials, its validity period is more obvious than that of blue treatment, and the hardness and wear resistance of the treated materials are significantly improved.
4. Special heat treatment process
Special heat treatment process is the product of technical development in recent years, including induction heating quenching, laser surface quenching, etc. Induction heating quenching is caused by high-frequency electromagnetic induction eddy current. The heating temperature rises rapidly and the surface hardness increases significantly, but softening point is easy to appear. In general, discontinuous heating can be used to extend the austenitizing time. Laser surface hardening This process uses laser as a heat source to rapidly heat and cool the metal surface, so that the internal substructure of austenite grains is smaller than recrystallization to obtain ultra-fine structures.
The above is an introduction to the heat treatment process of powder metallurgy materials by Zhongwei Precision. The heat treatment of powder metallurgy materials depends on their chemical composition and grain size. The existence of pores is an important factor, and powder metallurgy materials are extruded. In the sintering process, the pores formed pass through the whole part, and the existence of pores affects the way and effect of heat treatment








