Explanation of common terms of metal injection molding/powder metallurgy(一)
Feb 21, 2023
Explanation of common terms of metal injection molding/powder metallurgy(一)
January 19, 2015 cnpim
1、 Common powder injection molding materials in Chinese and English
1. Heavy metal
Sintered material with density not less than 16.5g/cm3. For example, tungsten alloys containing nickel and copper.
2. Cermet
A sintered material composed of at least one metallic phase and at least one nonmetallic phase with ceramic properties.
3. Sintered part
Sintered products formed by powder and strengthened by sintering usually have the characteristics of precise tolerance and easy installation.
4. Sintered structural part
Sintered parts usually used for mechanical manufacturing, excluding bearings, filters and friction materials.
5. Oiling-retaining bearing
The opening is impregnated with the sintered bearing of lubricating oil.
6. Sintered metal filter
Permeable sintered metal parts usually used for solid-liquid or solid-gas separation.
7. Sintered magnetic part
Sintered parts that meet magnetic requirements.
8. Sintered friction material
This sintered material is a composite material composed of a metal matrix and a metal or non-metallic additive, which is used to change the friction and wear characteristics of the material.
9. Sintered electrical contact material
Sintered materials with high conductivity and arc corrosion resistance, such as tungsten copper, tungsten silver, silver graphite and silver cadmium oxide composites
10. Hardmetal or tungsten carbide or cemented carbide
2、 Terminology related to the names and characteristics of various metal/ceramic powders
Powder
It usually refers to the aggregate of discrete particles with the size of 0.1um~1mm.
Slurry
A castable viscous dispersion system formed by powder in liquid.
Blank feedstock
Plasticized powder used as raw material for injection molding or powder extrusion.
Atomized powder
A powder of molten metal or alloy dispersed into droplets and solidified into single particles.
(The dispersion medium is usually high-speed air or liquid flow)
Carbonyl powder
Powder prepared by thermal dissociation of metal carbonyl compounds.
Electrolytic powder
Powder obtained by electrodeposition.
Reduced powder
Powder made by reducing metal compounds by chemical reduction.
Sponge powder
The porous reduction powder is made by crushing the highly porous metal sponge obtained by reduction method.
Alloy powder
Metal powder prepared by partial or complete alloying of two or more components.
Pre-alloyed powder
It usually refers to fully alloyed powder made by atomizing the melt.
Composite powder
Each particle is a powder composed of two or more different components.
Coated powder
A composite powder formed by coating a layer of different ingredients on the surface of particles.
Blended powder
A powder made by mixing different batches of powder with the same nominal composition.
Binder
Substances added to the powder to improve the strength of the compacts or prevent powder segregation that can be removed before or during sintering.
Dopant
A small amount of material added into the metal powder to prevent or control the recrystallization or grain growth of the sintered body during sintering or use.
(Mainly used for tungsten powder metallurgy)
Lubricant
The material added into the powder to reduce the friction between particles and between the compact and the mold wall surface.
Plasticizer
Thermoplastic material used as binder to improve powder formability.
Granulation
The process of agglomerating fine particles into coarse particles to improve powder fluidity.
Mechanical alloying
The process of solid alloying with high-energy grinder or ball mill.
Apparent density
The mass per unit volume of powder free filling under specified conditions.
Bulk density
The mass of powder per unit volume measured under non-specified conditions.
Tap density
The mass per unit volume of the powder in the container after being compacted under the specified conditions.
Compressibility
The degree to which the powder is compressed under pressure is usually uniaxial compression in a closed die.
Formability
The ability of powder to be compressed into a certain shape and maintain this shape in subsequent processing is a function of powder fluidity, compressibility and compact strength.
Compression ratio
The ratio of the volume of the powder before pressing to the volume of the blank after demoulding.
Fill factor
The ratio of the height of the powder filling mold to the height of the blank after demoulding.
Liquidity
A qualitative term describing the flow of powder through a defined pore.
Hydrogen loss
The relative mass loss caused by heating metal powder or compact in pure hydrogen under specified conditions.
Specific surface area
Total surface area per unit mass of powder.
Particle size
Linear size of individual powder particles measured by sieving or other suitable methods.
Particle size distribution
The powder sample is divided into several levels according to the particle size, and the percentage of each level of powder (by mass, quantity or volume).
Grain size cut
The part of powder that is within the two nominal particle size limits after classification.








