5G Base Station Base MIM Parts
First understand a basic concept, the "G" of 5G refers to the meaning, not the frequency, but coincidentally, the frequency of 5G is indeed higher than that of 4G and 3G, because the low frequency cannot meet the requirements on the one hand, and it is also occupied.
Introduction of metal injection molding 5G base station base MIM parts
|
Titanium injection molding 5G base station base MIM parts |
|||||||||||||||
|
Item |
Material |
Production Process |
Sintering Temperature |
Mold |
Custom |
|
|||||||||
|
Pedestal |
316L |
Metal Injection Molding |
1500℃ |
To be customized |
Yes |
|
|||||||||
|
Chemical Composition |
C：≤0.030 |
||||||||||||||
|
Available Materials |
Low carbon stainless steel, titanium alloy (Ti, TC4), copper alloy, tungsten alloy, cemented carbide, high temperature alloy (718, 713) |
||||||||||||||
|
Finish |
Dimensional Accuracy |
Product Density |
Appearance Treatment |
Appropriate Weight |
|||||||||||
|
Roughness 1～5μm |
（±0.1%～±0.5%） |
92～95% |
Mirror Reflection |
0.03g～400g） |
|||||||||||
|
Mechanical properties |
Tensile strength σb (MPa): ≥480 |
||||||||||||||
|
Thermal conductivity (W/(m*K)) |
|
||||||||||||||
|
Heat treatment |
Solid solution 1010 ~ 1150 ℃ rapid cooling. |
||||||||||||||
5G base station range
First understand a basic concept, the "G" of 5G refers to the meaning, not the frequency, but coincidentally, the frequency of 5G is indeed higher than that of 4G and 3G, because the low frequency cannot meet the requirements on the one hand, and it is also occupied. However, the high frequency coverage is small, but the low frequency can solve this problem very well. Therefore, finding ways to rely on low frequencies is the way out. It is said that China Telecom has tested the 2100GHz N1 network. If there is a certificate, it should be promoted soon, and you have to keep your eyes open when buying a mobile phone.
Therefore, some netizens joked: "The higher the G, the smaller the coverage area, then it will be difficult to have one base station per person when it develops to 7g8g, just carry an optical fiber cable and connect it directly to the mobile phone, and when people go there, the line will be brought to the There." Actually, that's not the case.
Back to the question at the beginning, 5G coverage, according to data, in our lives, the coverage radius of 2G base stations is about 5-10 kilometers; the coverage radius of 3G base stations is about 2-5 kilometers; the coverage radius of 4G base stations is about 1-3 kilometers; what about 5G base stations? Simply put, the same coverage, the number of base stations required by 5G is about 3-4 times that of 4G; the same base station, the power consumption of 5G is about 3-4 times that of 4G. The transmit power of mobile phones is limited, which determines that the coverage of 5G base stations is very small, ranging from more than 100 meters to several hundred meters.
In fact, the unit power of the base station will be reduced, the radiation will be less, the scope of the fault will be smaller, and the signal of high-rise buildings will be better. The 3G coverage rate is high, the base station is few, the power of a single base station is high, the radiation near the base station is relatively large, and a large number of mobile phones cannot be used in case of failure. Each has its own merits. Due to the high frequency and poor signal penetration of 5G, the coverage radius of base stations is generally about 100-300 meters, and the number of 5G base stations will be more than twice that of 4G.
The coverage of 5G base station is generally the coverage of the wireless router at home, so the consumption of 5G base station base MIM parts is gradually 1.4-2 times that of 4G. Each base station uses about two bases, every 300 meters. Only one group is needed, and the whole country is 9.6 million square kilometers, which requires too many parts and components. It will take a long time for the 5G network to be built. Let us look forward to the changes that 5G will bring to me!
Send Inquiry
