
Smart Watch With PM Parts
Stainless steel watch straps are often worn in life, so what is a stainless steel watch strap? Generally, good Swiss watches are made of 316L steel, with the exception of Rolex (904L). 316L is the 300 series in the United States and Japan, which is a common austenitic stainless steel. According to GB, it should be 00Cr17Ni14Mo2. Its chemical composition and content (%) are: carbon (C) <=0.03, manganese (Mn) <=2.0, silicon (Si) <=1.0, nickel (Ni) 12-16, chromium (Cr) 16-18, Molybdenum (Mo) 1.8-2.5, sulfur (S) <=0.030, phosphorus (P) <=0.035.
Product Description
|
Smart Watch with PM Parts |
|||||
|
Item |
Material |
Production Process |
Sintering Temperature |
Mold |
Custom |
|
Smart Watch |
440c |
Powder metallurgy sintering |
1550°C |
To be customized |
Yes |
|
Chemical composition |
C: 0.95~1.20 Si: ≤1.00 Mn: ≤1.00 S : ≤0.030 P : ≤0.035 Cr: 16.00~18.00 Ni: allowed to contain ≤0.60 |
||||
|
Available Materials |
Low carbon stainless steel, titanium alloy (Ti, TC4), copper alloy, tungsten alloy, hard alloy, high temperature alloy (718, 713) |
||||
About the introduction of stainless steel watch strap
Stainless steel watch straps are often worn in life, so what is a stainless steel watch strap? Generally, good Swiss watches are made of 316L steel, with the exception of Rolex (904L).
316L is the 300 series in the United States and Japan, which is a common austenitic stainless steel. According to GB, it should be 00Cr17Ni14Mo2. Its chemical composition and content (%) are: carbon (C) <=0.03, manganese (Mn) <=2.0, silicon (Si) <=1.0, nickel (Ni) 12-16, chromium (Cr) 16-18, Molybdenum (Mo) 1.8-2.5, sulfur (S) <=0.030, phosphorus (P) <=0.035.
904L is a high chromium, nickel, molybdenum content, low carbon austenitic stainless steel with very good corrosion resistance. The corresponding GB should be 00Cr20Ni25Mo4.5Cu. Its chemical composition and content (%) are: C≤0.02, Fe42.0-53.0, Cr19.0-21.0, Ni24.0-26.0, Cu1.0-2.0, S≤0.035, Mo4.0-5.0, Mg≤ 0.01, P≤0.045, Si≤1.0.

Cleaning of stainless steel watch straps
Regarding the cleaning of stainless steel watch bands, if it is an expensive watch and the wearer cares about the price, it is recommended to go to the after-sales service center for cleaning. If you want to DIY, it is actually very convenient. The following editor will introduce you to two methods of cleaning stainless steel watch straps.
Cleaning method of stainless steel watch strap one:
Preparations: An old magazine, a clean piece of plastic wrap, an old toothbrush, and detergent.
Operation process:
First of all, we stack the plastic wrap and the magazine together, and then roll them together into a cylinder. This will prevent the book from getting wet when the strap is cleaned later. The watch is then worn on this rolled cylinder. Slowly enlarge the cylinder made of magazines until the strap is fully stretched and the watch will not fall off. This is first of all for the convenience of cleaning later, and more importantly, after the strap is stretched, the stains in the gaps of the strap can be cleaned.
The next step is to clean the strap. First clean the surface of the strap, and then clean the stains in the crevices of the strap. The connection between these gaps is very tight, so it is very difficult to clean the dirty things inside. Now these gaps are opened by the cylinder made of books, and the dirt inside can naturally be cleaned. Then clean the back of the strap, and also clean the stains on the surface first. Next, clean the stains in the crevices. Then the cleaning job is done. Finally, scrub the strap with clean water.
All the steps are done, all that remains is to put the strap in a cool place to dry.

Cleaning method of stainless steel watch strap two:
We soak the strap in boiling water with detergent for about 15 minutes. Because the connection between the buckles on this kind of watch strap is very tight, the cylinder made of books cannot support the gap at the connection. Putting it in hot water uses the principle of heat expansion and contraction, so that the gaps at the joints expand by themselves, which is more convenient for cleaning. The next step is to clean the watch strap. The method is similar to method 1 and is omitted here.
After cleaning, soak the strap in cold water for about 15 minutes. The purpose of this is, first, to clean the detergent on the watch strap; second, to use the same principle of heat expansion and contraction to restore the gap where the watch strap rises to its original state. After soaking, also dry the strap in the shade.
Metal Injection Molding Process

Detection Systems


Send Inquiry









