
Architectural Accessories Lost Wax Castings
Building accessories are components other than building components that assist building construction and construction, such as scaffolding, pipe thread regulators for building construction, building tie rods, triangular building brackets, steel bar joints, etc. Building components are the main components of a house, including columns: frame columns, independent columns, structural columns, concrete short limb columns, columns, L-shaped columns; brick columns, concrete columns, and wooden columns.
Product Introduction
|
Architectural Accessories Lost Wax Castings |
||||||||
|
Item |
Material |
Production Process |
Sintering Temperature |
Mold |
Custom |
|||
|
Architectural Accessories Lost Wax Castings |
Customized according to customer requirements |
Investment Casting |
1680℃ |
To be customized |
Yes |
|||
|
Chemical composition |
|
|||||||
|
Available Materials |
Carbon steel, alloy steel, aluminum alloy, low carbon stainless steel, titanium alloy (Ti, TC4), copper alloy, high temperature alloy (718, 713) |
|||||||
|
Smoothness |
Dimensional accuracy |
Product density |
Appearance treatment |
Appropriate weight |
||||
|
Roughness 1~5μm |
(±0.1%~±0.5%) |
7.8g/CM³ |
According to customer requirements |
3g~4kg) |
||||
Building accessories are components other than building components that assist building construction and construction, such as scaffolding, pipe thread regulators for building construction, building tie rods, triangular building brackets, steel bar joints, etc.
Building components are the main components of a house, including columns: frame columns, independent columns, structural columns, concrete short limb columns, columns, L-shaped columns; brick columns, concrete columns, and wooden columns.
Beams: frame beams, connecting beams, lintels, ring beams, cantilever beams, arc beams; steel beams, wooden beams, concrete beams.
Board: cast-in-place board, prefabricated slab, prefabricated hollow board; reinforced concrete board, wood board.
Wall: brick wall, concrete wall, roof parapet, lightweight partition wall.
Door: solid wood door, plywood door, steel door.
Windows: steel windows, wooden windows, aluminum alloy windows, plastic steel windows.
































Construction accessories account for about 3%-5% of home improvement costs. The proportion is small, but it cannot be ignored. It uses functions divided into general categories. Common architectural hardware accessories include locks, hinges, slide rails, handles, hanging wheels, nails, board brackets, door stoppers, clothes hooks, bumper beads, bumper cards, board pins, etc. Hardware bathroom hardware is divided into categories and kitchen accessories. I'm only introducing the commonly used common categories, categories.
In general, the dimensional accuracy of steel castings is affected by many factors such as casting structure, casting material, mold making, shell making, roasting, pouring, etc. Any link setting and unreasonable operation will change the shrinkage rate of castings. As a result, the dimensional accuracy of the casting deviates from the requirements.
The following are factors that can cause defects in the dimensional accuracy of cast fittings
(1) Influence of the casting structure of building accessories:
a. The wall of the casting is thick and the shrinkage is large, and the wall of the casting is thin and the shrinkage is small.
b. The free shrinkage rate is large, and the hindered shrinkage rate is small.
(2) Influence of the casting material of building accessories:
a. The higher the carbon content in the material, the smaller the linear shrinkage, and the lower the carbon content, the larger the linear shrinkage.
b. The casting shrinkage rate of common Architectural Accessories Lost Wax Castings is as follows: casting shrinkage rate K=(LM-LJ)/LJ×100%, LM is the cavity size, and LJ is the casting size. K is affected by the following factors: wax pattern K1, casting structure K2, alloy type K3, and pouring temperature K4.
(3) The effect of mold making on the linear shrinkage of castings:
a. The influence of wax injection temperature, wax injection pressure, and pressure holding time on the size of the investment mold is obvious with the injection wax temperature, followed by the wax injection pressure. The pressure holding time has little effect on the final size of the investment mold after the investment mold is formed.
b. The linear shrinkage of the wax (mold) material is about 0.9-1.1%.
c. When the investment mold is stored, it will further shrink, and its shrinkage value is about 10% of the total shrinkage. However, after 12 hours of storage, the size of the investment mold is basically stable.
d. The radial shrinkage rate of the wax mold is only 30-40% of the shrinkage rate in the longitudinal direction, and the influence of the wax injection temperature on the free shrinkage rate is far greater than the impact on the hindered shrinkage rate (the best wax injection temperature is 57-59 ° C, the temperature The higher the contraction, the greater the contraction).
(4) Influence of shell material:
Zircon sand, zircon powder, Shangdian sand, and Shangdian powder are used, because of their small expansion coefficient, only 4.6×10-6/℃, so they can be ignored.
(5) Influence of shell roasting:
Due to the small expansion coefficient of the shell, when the shell temperature is 1150°C, it is only 0.053%, so it can be ignored.
(6) Influence of casting temperature:
The higher the pouring temperature, the greater the shrinkage, and the lower the pouring temperature, the smaller the shrinkage, so the pouring temperature should be appropriate.
Detection Systems

Copper Silica Sol Investment Casting


Send Inquiry









