18C3 Lost Wax Investment Casting
18C3 Lost Wax Investment Casting
video
18C3 Lost Wax Investment Casting
da60cc749eabaa2a31858434cf253762_8921748492_276315650
ec0a3d285fa4f2b58642ebe7a608910c_8959265204_276315650
1/2
<< /span>
>

18C3 Lost Wax Investment Casting

18C3 lost wax investment casting has high strength and hardenability. The critical hardenable diameter in oil reaches 4 to 22mm, and the critical hardenable diameter in water reaches 11 to 40mm.

Product Introduction

18C3 lost wax investment casting

Item

Material

Production Process

Sintering Temperature

Mold

Custom

18C3 lost wax investment casting

18C3

Molten mold casting

1380℃

To be customized

Yes

Chemical composition

C: 0.18~0.24

Si: 0.17~0.37

Mn: 0.50~0.80

Cr: 0.70~1.00

S: Allowable residual content ≤0.035

P: Allowable residual content ≤0.035

Ni: Allowable residual content ≤0.030

Cu: Allowable residual content ≤0.030

Available Materials

Carbon steel, alloy steel, aluminum alloy, low -carbon stainless steel, titanium alloy (TI, TC4), copper alloy, high temperature alloy (718, 713)

Smoothness

Dimensional accuracy

Product density

Appearance treatment

Appropriate weight

Roughness 1~5μm

(±0.1%~±0.5%)

7.8g/CM³

According to customer requirements

3g~4kg)

 

18c3 an alloy structural steel

18C3 is a kind of alloy structural steel. This steel is mostly used to manufacture carburized parts (oil quenching) that require high core strength, bear surface wear, have a cross-section below 30mm, or have complex shapes and low loads.

 

Attributes

18C3, alloy structural steel. Unified digital code: A20202

Standard GB/T 3077-1999 GB/T 17107

 

Application

This kind of steel is mostly used to manufacture carburized parts (oil quenching) that require high core strength, are subject to surface wear, have a cross-section below 30mm, or have complex shapes and low loads, such as machine tool gearbox gears, gear shafts, and cams. , worm, piston pin, claw clutch, etc.; for parts with small heat treatment deformation and high wear resistance, high-frequency surface quenching should be performed after carburization, such as gears, shafts, splined shafts with a module less than 3, etc. This steel can also be used in the quenched and tempered state to manufacture parts that work at high speeds and withstand moderate impact loads. This steel can also be used as low-carbon martensitic quenching steel to further increase the yield strength and Tensile strength (approximately 1.5 to 1.7 times increased).

 

Features

18C3 lost wax investment casting has high strength and hardenability. The critical hardenable diameter in oil reaches 4 to 22mm, and the critical hardenable diameter in water reaches 11 to 40mm. However, the toughness is poor. This steel still remains when carburized. The grains tend to grow, and direct quenching at low temperatures has a greater impact on the impact toughness, so a second quenching is required after carburizing to improve the toughness of the core of the part without tempering brittleness; steel has high cold strain plasticity and can be wire drawn in a cold state; The machinability is good under high-temperature normalizing or quenching and tempering conditions, but is poor after annealing; the weldability is good, and heat treatment is generally not required after welding, but parts with a thickness greater than 15mm need to be preheated to 100~150°C before welding.

 

Chemical composition

(mass fraction) (%)

Carbon C: 0.18~0.24

Silicon Si: 0.17~0.37

Manganese Mn: 0.50~0.80

Chromium Cr: 0.70~1.00

Sulfur S: Allowable residual content ≤ 0.035

Phosphorus P: Allowable residual content ≤0.035

Nickel Ni: Allowable residual content ≤0.030

Copper Cu: Allowable residual content ≤0.030

 

Delivery Status

Delivery with heat treatment (normalizing, annealing, or high-temperature tempering) or without heat treatment, the delivery status should be specified in the contract.

 

Detection Systems

 

product-600-694

 

Copper Silica Sol Investment Casting

 

product-600-450

product-600-450

 

Send Inquiry

(0/10)

clearall