Tungsten Steel Valve Seat Ball PM Sintered Parts
Tungsten Steel Valve Seat Ball PM Sintered Parts
video
Tungsten Steel Valve Seat Ball PM Sintered Parts
b975843729cb0b0b23e5e1c5d0c3564d_7b87cf08-d06a-4b0e-8fd0-6a7f06aa2b16.jpg_500xaf
1/2
<< /span>
>

Tungsten Steel Valve Seat Ball PM Sintered Parts

In polycrystalline silicon, coal chemical industry, power plant ash removal, mud and boiler slag discharge, and other material transportation pipelines, the sealing part of the valve is not only affected by the sliding friction and wear of the sealing sub-components, but also withstands the high-speed impact of high-temperature, high-hardness, gas-solid two-phase mixture, and high pressure. Fluid-induced flashing and cavitation, which in turn leads to damage and exacerbates valve failure.

Product Introduction

Tungsten steel valve seat ball PM sintered parts

Item

Material

Production Process

Sintering Temperature

Mold

Custom

Tungsten steel valve seat ball powder metallurgy

Carbide

Powder metallurgy pressing

1380℃

To be customized

Yes

Chemical composition

C:0.42~0.50;

Cr: ≤0.25;

Mn: 0.50~0.80;

Ni: ≤0.25;

P: ≤0.035;

S: ≤0.035;

Si: 0.17~0.37

Available Materials

Low carbon stainless steel, titanium alloy (Ti, TC4), copper alloy, tungsten alloy, hard alloy, high temperature alloy (718, 713)

Smoothness

Dimensional accuracy

Product density

Appearance treatment

Appropriate weight

Roughness 1~5μm

(±0.1%~±0.5%)

7.3-7.6g/CM³

According to customer requirements

0.03g~400g)

 

In polycrystalline silicon, coal chemical industry, power plant ash removal, mud and boiler slag discharge, and other material transportation pipelines, the sealing part of the valve is not only affected by the sliding friction and wear of the sealing sub-components, but also withstands the high-speed impact of high-temperature, high-hardness, gas-solid two-phase mixture, and high pressure. Fluid-induced flashing and cavitation, which in turn leads to damage and exacerbates valve failure. Therefore, under severe working conditions such as powder conveying, wear resistance has become an important performance evaluation index for valves.

 

Analyze

According to the conditions and mechanism of friction, there are many different forms of wear, the common ones are abrasive wear, adhesive wear, fatigue wear, corrosion wear, and erosion wear.

The commonly used parameters to characterize the wear performance of materials are wear amount, wear rate, wear degree, wear resistance relative wear resistance, etc. The basic requirement for abrasive wear is that the surface of the object must have high hardness (the surface hardness should exceed the hardness of the abrasive), and it should also have good oxidation resistance at working temperature, an effective way to control or minimize wear It is to improve the hardness and wear resistance of the material. Sintered tungsten carbide has high strength and a high surface finish. When paired with other materials, the friction coefficient is smaller than that of steel, which can significantly reduce the friction of the contact surface and effectively reduce the operating torque.

 

Features

Tungsten steel valve seat ball PM sintered parts are made of a mixture of tungsten and carbon heated at high temperatures. Most tungsten carbides have very high hardness, and their microhardness is second only to diamonds. The melting point is 2870°C. The boiling point is 6000°C, and the relative density is 15.63 (18 ℃), not easy to decompose at high temperatures, and has good oxidation resistance. The investigation of the field use shows that the wear resistance of tungsten carbide is 100 times higher than that of tool steel, stainless steel, iron, and brass under the conditions of abrasive wear, erosion wear, and abrasion, and its rigidity is 2 to 3 times higher than that of steel. , 4 to 6 times higher than cast iron and brass, and the impact resistance is similar to that of hardened tool steel.

 

Application

In coal gasification and polysilicon and other high-temperature, high-pressure, highly corrosive, and solid particle-containing slurry and powder working conditions, conventionally used hard-sealed ball valves, Venturi black water control valves, pulverized coal control valves, and disc valves The valve disc and valve seat of the slide valve and the slide valve are respectively made of sprayed tungsten carbide hard alloy to form the sealing pair. Since the thickness of the tungsten carbide coating is less than 2mm, the hardness is less than 60HRC, and the bonding force between the coating and the substrate is less than 1000psi. Spraying is usually carried out at a high temperature of 10,000°C, and the operating and construction conditions are harsh. The service life of the valve is difficult to guarantee 10,000 cycles, and it cannot meet the long-term stable production requirements of systems such as coal chemical slurry and polysilicon powder. On the other hand, the strength of sprayed tungsten carbide is mainly provided by the base material. When the linear expansion coefficient of the two materials is large, the use is limited by the temperature, and it is difficult to exceed 450°C. The discs and seats of the new hard-sealed ball valves, Venturi black water control valves, pulverized coal control valves, disc valves, and slide valves are all made of integrally sintered tungsten carbide hard alloy to form the sealing pair, and the performance of the valves has been significantly improved.

 

Metal Injection Molding Process

 

product-800-600

 

Detection Systems

 

 

1661141928831

1661509092764001

 

Send Inquiry

(0/10)

clearall